2021-08-29

The reasons for not spinning the washing machine and what are the correct ways to avoid this problem

The washing machine plays an important role in domestic life, as it assumes the task of washing clothes, through some steps and stages, including spinning, but sometimes clothes may come out wet as they are, and the reasons for not squeezing clothes remain vague and have no Answers, and therefore the washing machine loses its importance among the rest of the other electrical appliances, but there is no problem without a solution, and the following article provides a detailed dose of the reasons that prevent clothes from being spun, in addition to solutions to overcome that problem.
Not spinning the washing machine
The stage of squeezing clothes is the last stage in the well-known washing cycle, where the washing machine first starts with drawing water to fill the drum, then it starts rotating right and left, to come the stage of expelling the water from the expulsion hose, to move to the rinsing stage, and finally to the age, and this stage where the motor rotates In one direction quickly, but the surprise may occur, which is the washing machine not squeezing the clothes, so what is the reason for that?! 
Reasons for not spinning the washing machine
Jurisprudence begins to find out the reasons for not squeezing the clothes, which in turn will lead to wet clothes, and the washing machine may be damaged, and therefore the usual washing cycle has not completed its cycles and stages, making the task of drying clothes difficult, but in the following lines will be presented the reasons that prevented The completion of the wash cycle, which may be technical related to the washing machine itself, or related to the lack of knowledge of some simple information, as shown in the following: 
Increase the load on the washing machine
It is known that the first steps of washing are putting the clothes in the drum, after which the powder is placed, and the washing machine program is set and then run. The engine is very powerful, and the number of revolutions of the drum reaches 1200 rpm, which leads to its overheating, and the engine begins to break down with increased wrong use, which leads to damage to the motor and the washing machine.
Unbalanced clothes in the washing machine
This reason may be similar in its pronunciation to what preceded it, but it is completely different from it. What is meant here is the misdistribution of clothes inside the suit, in other words, focusing on placing most of the clothes in one side, which leads to an increase in the load on the motor, which leads to its inability to rotate. quickly, and thus the washing machine loses its ability to squeeze clothes as required, and the losses will not stop there, but the motor will be damaged, in addition to all the parts that participated in the success of the spinning process.
A problem with the pump connections
The expulsion pump is mainly responsible for drawing water from the washing machine drum, and pushing it out into the drain stream through the drain hose, but there may be a problem such as not enough electricity to reach one of those connections, or it goes out of its rightful place inside the refrigerator body, and therefore it will not be based on expelling Water from the washing machine, which results in the washing machine not squeezing clothes. 
Ejection pump damaged
The same problem may be in the ejection pump and not its connections. The damage that may be caused to it, such as the gathering of fibers and the remnants of clothing around the feather, or the breakage of the feather itself, affects the ability to perform its role, which we mentioned earlier, and it may worsen with increased wrong use, and damage some other parts, causing aggravation of the problem. 
Drain hose clogged
The spinning process is based on expelling water from the washing machine through the rubber drain hose, and therefore if the washing machine does not wring the clothes, the hose is likely to be clogged with bristles or fibers accumulated from previous washing operations, and it may be due to obstacles inside the washing machine filter - which is present in some types Prevents water from escaping through it and reaching the drain hose. Some washing machines may complete the washing cycle without expelling the water, and therefore do not wring and the clothes remain wet, and others stop the washing machine after the first wash, and an error code appears on the electronic screen, which means that there is a problem that hinders the process of expelling the water, and completing the cycle correctly, which requires Check the drain hose, making sure that it is intact at an appropriate height, and is not twisted, in addition to checking the internal washer filter.
Drainage obstruction
The drain hose may be in its best condition, and it does not suffer from any twisting or blockage, and before that, the internal filter of the washing machine is in good condition, and there is nothing that can hinder it, so the problem becomes in the blockage of the drain stream, which takes over the task of transferring water from the hose to the drain directly It may be clogged with fibres, bristles and other deposits, which requires the use of self-efforts to clean it.
Washing machine belt failure
The washing machine drum is connected to a basic metal part, which is the drum, and it connects with the motor with a belt, but sometimes this belt may fall, and thus the washing machine loses its ability to spin, causing disruption of the spinning process, and the failure of the washing cycle in general, and the reasons must be revealed The belt falls before replacing it, the problem may be either due to the end of its lifespan, or the presence of something impeding its movement, so choosing the solution depends on knowing the cause. 
Malfunction of the washing machine motor
The motor or the motor is the most important part of the washing machine, with it, all the different processes are carried out in the washing machine in general, and its inability to spin in particular, because there is a defect in it, the washing machine will not be able to spin, and therefore its inability to spin, and the reason may be a defect in the special electrical connections With the motor, or moving electrical circuits from their place, it is tedious, it is necessary to contact a specialized technician.
Malfunction of the washing machine panel
The importance of the electronic board is similar to the importance of the maestro who leads the orchestra, as she is the one who leads the process

We are the only authorized agent in Egypt from General Electric

General Electric